TESEQ KEMZ 801 EM電磁鉗

符合IEC/EN 61000-4-6標準高效耦合適用于所有線纜上堅固設計

產品特點： IEC 61000-4-6 (EN 61000-4-6) 定義了三種基本傳感器類型，用于將測試信號注入測試設備中。基本要求是將已知的射頻信號注入在每個測試頻率的被測件的線纜上，并確定被測件是否繼續正常運行。因此，有必要將輔助設備從測試信號上分開。否則就很難知道故障是來自于被測件或輔助設備。雖然耦合去耦網絡(CDN)是實現這一測試的好的方法，而且在某些環境下也必須使用這一方法，但它并不是都要使用CDN。

IEC 61000-4-6 (EN 61000-4-6) defines three basic types of transducer used for the injection of test signals into the equipment under test (EUT). The basic requirement is to inject a known level of RF signal onto the cable of the EUT at each test frequency and to determine whether the EUT continues to function correctly. In order to do this, it is necessary to decouple the auxiliary equipment (AE) from the test signal. If this not achieved it is difficult to know whether any fault is due to a failure of the EUT or the AE. Whilst the coupling/decoupling network (CDN) is one of the best ways to achieve this test and indeed it is mandatory to use them under some circumstances, it is not always possible to use a CDN. The normative Annex A of IEC/EN 61000-4-6 gives additional information regarding the clamp injection. The KEMZ 801A is similar to the described EM clamp in the standard and injects the disturbance signal through a combination of inductive and capacitive coupling. The use of a ferrite cores along the length of the clamp also improves the common mode impedance of the test set-up and the reproducibility of the test. Optionally offered is the calibration kit CAL 801A which allows test level setting and correction factor measurement. Frequency range: 10 kHz to 1000 MHzNominal impedance: 50 ΩConnector: N-type female Maximum input level 0.01 to 100 MHz: 100 W for 15 min 100 to 230 MHz: 100 W for 3 min 230 to 1000 MHz: 50 W for 3 minMaximum correction factor 0.15 to 400 MHz: 4 dB (50 Ω system), 13.5 dB (150 Ω system)Maximum cable diameter: 20 mmDimension (LxH): 647 mm x 130 mm x 105 mmWeight: approx. 7 kg Dimensions: see drawingMaximum length of the clamp: 670 mmConnectors on the clamp side: 4 mm bananaRF connector: N-type female Weight: approx. 640 gPower requirements in accordance with IEC/EN 61000-4-6 (6 dB attenuator, 0.5 dB cable loss, typical insertion loss of KEMZ 801A) calibration level for 3 V EMF without modulation, 3 V EMF with AM 80%, calibration level for 10 V EMF without modulation, 10 V EMF with AM 80%, calibration level for 20 V EMF without modulation, 20 V EMF with AM 80% calibration level for 30 V EMF without modulation, 30 V EMF with AM 80% Max. forward power on the 6 dB attenuator inputPart number Description 255100 KEMZ 801A EM Clamp, conform with IEC/EN 61000-4-6 255102 KEMZ 801AS EM Clamp, conform with IEC/EN 61000-4-6, supplied with calibration set CAL 801A 255103 KEMZ 801AS50 EM Clamp, conform with IEC/EN 61000-4-6, supplied with calibration set CAL 801A and 50 ? termination 1 W 97-235501 KEMZ 801-TC Traceable calibration (ISO17025), order only with KEMZ 801A255101 CAL 801A Calibration unit for KEMZ 801A

TESEQ KEMZ 801 EM電磁鉗

深圳市美佳特科技有限公司（簡稱“美佳特"）成立于2010年，致力于光通訊測試、通用電子測量及5G測試服務。美佳特以“無線溝通，溝通無極限 "企業使命，業務聚焦于精密測試測量儀器的租賃、銷售、維護、計量及測試環境搭建等一站式服務。N2843A Keysight 無源探頭 Keysight 是德

主營產品：示波器主機和模塊、眼圖儀、光譜儀、信號源、頻譜分析儀、網絡分析儀、阻抗分析儀、光通信儀器、誤碼儀、光時域反射儀、可調諧激光源、光功率計、光衰減器等。合作品牌：安捷倫、是德、泰克、安立、愛得萬、安騰、力科、馬可尼（IFR）、R&S、EXFO等。N2843A Keysight 無源探頭 Keysight 是德

主推：Agilent 86100D/C 示波器,keysight M8195A 任意波形發生器,Anritsu MS9740B/A 光譜分析儀,YOKOGAWA AQ6370D/E 光譜分析儀,keysight N1092A/C 采樣示波器,keysight E8257D 模擬信號發生器,keysight E5071C 矢量網絡分析儀